55W Car HID Xenon Headlight H1 H3 H7 H8/H9/H11 9005 Bulbs Ballasts Error Free DE

Why choose our Digital HID Conversion kits?

* 100% Plug and Play design. Ballasts had the EMC built in it,and the mini size ballasts are save the space get more easier to install and more stable.

* Our product comes with a 3 year warranty and easy installation. We stand behind our hid kits with support and service like other company.

* We offer a wide range of options including 6 bulb sizes, 7 different colors and 2 types of ballasts. Not only do we sell the conversion kits, but all the accessories needed for proper installation on most vehicles.

* 6 hours continuous working aging test.

* Connection circuit protection test.

* Short circuit protection test.

* Lack of voltage protection test.

* Over voltage protection test.

* Flash light concussion test.

* Quakeproof capability test.

* Cold, warm boot test.

* Polarity protection test.

* EMC anti-jamming test

What is HI/LO Bi-Xenon?

* This will depend on the type of vehicle you drive. For most vehicle, the headlights have 2 bulbs each: one for low beams and one for high beams. In this case, you will need one regular HID kit for the low beams. If you also want your high-beams to be HID lights, you will need a second regular HID kit. * On some other vehicles, the headlights have one bulb each. This bulb performs the function of both the high beam and low beam. In this case, if you want to keep the high beam and low beam functions, you will need to install a special HI/LO kit. The HI/LO HID kits have special bulbs that perform both high and low beam functions. * A Bi-Xenon bulb replaces a H4 halogen bulb that produces low beam as well as high beam. A H4 halogen bulb has therefore two filaments, one for low beam and one for high beam. The Bi-Xenon bulb however, only has one 'light cell'. (See The Pic. Below) By means of an ingenious electro-magnetic construction, this light cell can change position. One position is low beam, the other is high beam.

HID Color Temperature:

* The color of light is measured and expressed in degrees Kelvin (K). The color spectrum ranges from a red to purple. HID headlamps do not have this wide of a range though there are different bulbs that skew toward either extreme. Most are more focused on the center of that range. * 4,300K is the temperature that is closest to natural daylight. Factory HID headlamps are setup for this color temperature.

Our Benefits of Slim Ballast:

Slim Ballasts usesmaller internal components and still offer the same input and output power as its standard sized version. With the Igniter unit in an epoxy filled chamber, we are able to reduce the size of the core unit by roughly half, also reducing the weight significantly. Slim Ballasts are easier to mount, weigh less, and allow users to install their HID systems faster with less time spent under the hood, and more time enjoying their HID lights!

Installation Guide:

Step 1: Open hood and locate the factory light bulb you are trying to convert. If fog lights, you may need to pull out your factory fog light housing to access the back. On some vehicles you can access factory bulbs from the engine bay or from the wheel wells with your wheels fully turned on direction. Please consult your owners manual or dealer on how to access your factory light bulbs. In 90% your bulbs are easily removed without too much trouble. Once your factory light bulb is removed, you can prepare for the HID bulb insertion.

Step 2: Remove the plastic capsule preinstalled on the HID bulb and insert into your headlight socket. HID bulbs should fit similar to your factory light bulb, but the tolerances may be slightly different on certain vehicle models. Bulb installation will vary from twisting to clamping from the back depending on the bulb type. Be very gentle with the HID glass portion. Do not touch the glass with your fingers. If it does end up getting dirty, simply wipe with clean cloth gently.

Notice: Some vehicle models may require adapters for the bulb to fit into the socket. These include H7 bulbs. Some parts off of your original headlight may be be required depending on car model. Example, 9007 light bulbs will require the reinstallation of the plastic bulb holder adapter. Some BMW / VW / Mercedes / Saab will require a metal adapter or plastic adapter to hold the bulb in place.

Step 3a: Once the HID bulb is fixed into place locate the factory connector where the original halogen bulb was connected to. You will now connect the supplied wire (may be a plug or 2 metal tips) that you must insert into your factory connector as shown below. When we say factory connector, this is the connector your original bulb was feed power with.

If you purchased a Bi-xenon kit, or a kit with relay, your installation will be a little different than above. See steps 3b or 3c.

Step 3b: If your kit included a relay you will not use the provided extra wires shown in Step 3a. that connect ballast to factory headlight plug. Instead the ballast get connected to the relay as shown below. The relay then will connect to your factory headlight plug. Some relays will have two plugs one for each side, while others only one headlight plug. Remember a relay simply gets a signal from your headlight plug, then allows power to flow directly from your battery.

Step 3c: If your kit purchased is a bi-xenon kit also known as hi/low (low beam + high beam HID with movement). This only applies to kits with bulb types 9004 9007 H4 H13 9008. Notice on these kits there will be only 1 headlight plug connector. One of your headlight connectors may not be used.

Step 4: Before mounting ballast permanently please test the system. Low beam, high beam and fog light function if it applies to your install. It is best to turn the vehicle on to test the system as some vehicles do not give full voltage when vehicle is running only from battery.

Step 5: Mount the ballasts on any existing bolt or flat surface away from excessive heat. We do not recommend mounting on top of the radiator or in front or behind it. Ballasts are electronic devices which excessive heat can ruin. Make certain the wires with your kit cannot get tangled into the belt line or are resting on very hot components of the engine.

• Payment Method
• Shipping and Handing Time
• Returns
• Feedback
• Contact us

Q1: What can I do if I haven't received my item in time? A1: Please find the order record, select "Contact seller" in drop-down menu at right hand side, which lead to a new page and "Select a topic" as follows, then we will receive your email and respond within 24 hours.

Q2: How can we process if I'm not satisfied with your product? A2: Please click " Return this item" bottom, find the following 3 options, and select one among them to continue should be okay. PS: The return reasons are not important, as no matter which one you select, we need to further confirm the details through message.

Saturday: -09:00-12:00(GMT+8) -14:00-17:00(GMT+8)

All emails would be replied very fast during our working time, emails would be replied within 24 hours usually during holiday. Welcome to contact us if you have any problem.　

Q1: What can I do if I haven't received my item in time? A1: Please find the order record, select "Contact seller" in drop-down menu at right hand side, which lead to a new page and "Select a topic" as follows, then we will receive your email and respond within 24 hours.

Q2: How can we process if I'm not satisfied with your product? A2: Please click " Return this item" bottom, find the following 3 options, and select one among them to continue should be okay. PS: The return reasons are not important, as no matter which one you select, we need to further confirm the details through message.

Saturday: -09:00-12:00(GMT+8) -14:00-17:00(GMT+8)

All emails would be replied very fast during our working time, emails would be replied within 24 hours usually during holiday. Welcome to contact us if you have any problem.　

• Bluetooth Mini Pocket Thermal Drucker Mobile Phone Photos Label Printing Machine

  30.56 EUR

  Free shipping

• Mini Pocket Thermal Drucker Bluetooth Mobile Phone Photos Label Printing Machine

  30.57 EUR

  Free shipping

• LED High Bay Light 100-500W Low Bay UFO Factory Warehouse Garage Industrial Lamp

  38.18 EUR

  Free shipping

• Elektrisch Zahnaufhellungs-Kit Tooth Cleaner Dental Tool Plaque Calculus Remover

  3.95 EUR

  Free shipping

• Mini Kabelloses Lavalier-Mikrofon Wireless Steckmikrofon für Android/iPhone

  1.0 EUR

  Free shipping

• Data Ladekabel für iPhone Kabel 1M Schnellladekabel Datenkabel für iPhone/iPad

  1.0 EUR

  Free shipping

• LCD Display MPPT Solar Panel Regulator Laderegler Auto 12V/24V System 100A 2-USB

  23.71 EUR

  Free shipping